BMW E60 5-Series Forum | 5Post.com  
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read  

Go Back   BMW E60 5-Series Forum | 5Post.com > BMW 5-Series (E60) Forums (2004 - 2009) > General 5-series and M5 (E60) Forum

Post Reply
 
Thread Tools Search this Thread
      09-14-2020, 01:16 PM   #1
E92William
Banned
1998
Rep
2,026
Posts

Drives: 2008 E92 328xi
Join Date: Nov 2019
Location: Miami

iTrader: (0)

Garage List
2008 BMW 328xi  [0.00]
This 3 stage manifold is ready to install. Fully refreshed, cleaned and tested. Waiting to find an N52 as it's new home

I take apart the disa valve flaps and clean them, test the internals, grease them and put them back together and test how they work thoroughly to make sure they're in good working shape, most valves straight out of a used car will be faulty or slow so this is a huge plus to this manifold. Also these disas are both updated revision valves with no risk at all of anything dropping into the intake.

On a fully stock 525i N52 with the proper software (which I sell aswell) you can expect +45hp gain and +35lb ft of torque, even more gains in the midrange.

On a fully stock 528i N52 you can expect +30hp and +20lb ft of torque with even more gains in the mid range aswell.

Videos of valves working:
Large disa

Small disa


$320
I don't include shipping but depending where you live we can work something out

http://rover.ebay.com/rover/1/711-53...8;toolid=11111
Attached Images
       
Appreciate 0
      11-30-2020, 06:48 PM   #2
matress
New Member
0
Rep
14
Posts

Drives: 2008 BMW 528i
Join Date: Nov 2020
Location: Florida

iTrader: (0)

Has anyone on this forum every actually successfully done a 3-stage manifold swap for a 528i?
Appreciate 0
      11-30-2020, 10:49 PM   #3
E92William
Banned
1998
Rep
2,026
Posts

Drives: 2008 E92 328xi
Join Date: Nov 2019
Location: Miami

iTrader: (0)

Garage List
2008 BMW 328xi  [0.00]
Quote:
Originally Posted by matress View Post
Has anyone on this forum every actually successfully done a 3-stage manifold swap for a 528i?
I'm sure it has been done. I don't see a reason why it would fit on a 128i and 328i n52 and it wouldn't on a 528 with the exact same engine. As a matter of fact the F10 528s with the n52 come with the 3 stage manifold from factory
Appreciate 0
      12-01-2020, 10:51 PM   #4
mweine
Work Hard! Play Harder!!
mweine's Avatar
Canada
47
Rep
193
Posts

Drives: BMW 1M, BMW M3 CS
Join Date: Aug 2012
Location: Montreal, Quebec, Canada

iTrader: (1)

Garage List
1989 BMW M3  [0.00]
Quote:
Originally Posted by E92William View Post
This 3 stage manifold is ready to install. Fully refreshed, cleaned and tested. Waiting to find an N52 as it's new home

I take apart the disa valve flaps and clean them, test the internals, grease them and put them back together and test how they work thoroughly to make sure they're in good working shape, most valves straight out of a used car will be faulty or slow so this is a huge plus to this manifold. Also these disas are both updated revision valves with no risk at all of anything dropping into the intake.

On a fully stock 525i N52 with the proper software (which I sell aswell) you can expect +45hp gain and +35lb ft of torque, even more gains in the midrange.

On a fully stock 528i N52 you can expect +30hp and +20lb ft of torque with even more gains in the mid range aswell.

Videos of valves working:
Large disa

Small disa


$320
I don't include shipping but depending where you live we can work something out

http://rover.ebay.com/rover/1/711-53...8;toolid=11111
Would it increase the Hp and torque in an 2008 X3 3.0si with the highest tuned stock N52 at 276Hp?
Appreciate 0
      12-01-2020, 11:01 PM   #5
E92William
Banned
1998
Rep
2,026
Posts

Drives: 2008 E92 328xi
Join Date: Nov 2019
Location: Miami

iTrader: (0)

Garage List
2008 BMW 328xi  [0.00]
Quote:
Originally Posted by mweine View Post
Quote:
Originally Posted by E92William View Post
This 3 stage manifold is ready to install. Fully refreshed, cleaned and tested. Waiting to find an N52 as it's new home

I take apart the disa valve flaps and clean them, test the internals, grease them and put them back together and test how they work thoroughly to make sure they're in good working shape, most valves straight out of a used car will be faulty or slow so this is a huge plus to this manifold. Also these disas are both updated revision valves with no risk at all of anything dropping into the intake.

On a fully stock 525i N52 with the proper software (which I sell aswell) you can expect +45hp gain and +35lb ft of torque, even more gains in the midrange.

On a fully stock 528i N52 you can expect +30hp and +20lb ft of torque with even more gains in the mid range aswell.

Videos of valves working:
Large disa

Small disa


$320
I don't include shipping but depending where you live we can work something out

http://rover.ebay.com/rover/1/711-53...8;toolid=11111
Would it increase the Hp and torque in an 2008 X3 3.0si with the highest tuned stock N52 at 276Hp?
You could get there with supporting mods but in reality a manifold swap by itself won't get the car to that power level because well, no stock n52 ever came out with that power output. A lot of horsepower figures are mixed up with the euro n53 which puts out 272hp. With the bimmerlabs 330i tune you'd easily be at 258 which is right there with the 3.0si which is rated at 260, but the amount of power you make doesn't depend on the 3 stage by itself but rather what tune you run on the car.
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 04:52 AM.




5post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST