help....where to go from here?

humboldtinjun · 10-15-2024, 08:42 PM

hi i have a 2007 m5 and it was sitting for a couple years. I had the battery replaced and registered, and I had a light and limp mode. I took it to the shop and had both throttle actuators replaced. When i drove it, it drove fine but if i let it idle for 20 seconds at a stoplight, the check engine light comes on and sometimes goes into limp mode. if i restart it and drive it goes away unless i let it sit and idle again. I have replaced all the coils and spark plugs and Maf sensors. It helped but didnt fix the issue. the other thing i notived is my hud stopped working. Could this be a software issue? any help with this would be really appreciated as I am already heavily into it budgetwise.

Ralph III · 10-16-2024, 10:14 PM

You need to use a computer and ISTA software to pull whatever codes that your car is showing. Otherwise, you are just shooting in the dark.

Good luck,
Ralph

BMW_E_F_G · 11-14-2024, 05:57 PM

Hi Bud,

After dead battery all of the ecu's will throw a fault code. So if your dash looks like a Christmas tree don't panic.

After deleting these faults some of the hardware on the car needs to be recalibrated/adaption reset/relearn (like setting date and time after CMOS battery replacement, it cannot know otherwise what time it is) the problem will keep coming back otherwise even after replacing the part 1000 times, which was not needed in your case I'm afraid of.

So, not just delete the codes but do also adaptation of certain hardware that keeps showing a fault.

Greets

Taylyan

10-15-2024, 08:42 PM	#1
humboldtinjun Registered 0 Rep 2 Posts Drives: 2007 bmw m5 e60 Join Date: Oct 2024 Location: eureka california iTrader: (0)	help....where to go from here? hi i have a 2007 m5 and it was sitting for a couple years. I had the battery replaced and registered, and I had a light and limp mode. I took it to the shop and had both throttle actuators replaced. When i drove it, it drove fine but if i let it idle for 20 seconds at a stoplight, the check engine light comes on and sometimes goes into limp mode. if i restart it and drive it goes away unless i let it sit and idle again. I have replaced all the coils and spark plugs and Maf sensors. It helped but didnt fix the issue. the other thing i notived is my hud stopped working. Could this be a software issue? any help with this would be really appreciated as I am already heavily into it budgetwise.
	Appreciate 0 Tweet Quote

10-16-2024, 10:14 PM	#2
Ralph III Private First Class 112 Rep 111 Posts Drives: 2018 BMW 650i Gran Coupe Join Date: Apr 2023 Location: Alabama iTrader: (0)	You need to use a computer and ISTA software to pull whatever codes that your car is showing. Otherwise, you are just shooting in the dark. Good luck, Ralph
	Appreciate 1 MOEHQ3.00 Quote

11-14-2024, 05:57 PM	#3
BMW_E_F_G Private 48 Rep 52 Posts Drives: BMW M550i COMPETITION G30 2017 Join Date: Oct 2023 Location: Schiedam iTrader: (0)	Hi Bud, After dead battery all of the ecu's will throw a fault code. So if your dash looks like a Christmas tree don't panic. After deleting these faults some of the hardware on the car needs to be recalibrated/adaption reset/relearn (like setting date and time after CMOS battery replacement, it cannot know otherwise what time it is) the problem will keep coming back otherwise even after replacing the part 1000 times, which was not needed in your case I'm afraid of. So, not just delete the codes but do also adaptation of certain hardware that keeps showing a fault. Greets Taylyan
	Appreciate 0 Quote